What Should My Salt Chlorinator Be Set At?

How many hours a day should a salt water pool pump run?

8 hoursTypical pool pump operation is 8 hours per day, although it is not uncommon to run longer in the summer months (or with low speed variable speed pumps) or shorter in the winter when bather loads are light..

Why is my salt cell not working?

First, check power. If your salt cell is plugged into an GFI outlet, make sure that the test button is not popped, or tripped. If your salt system is hardwired, variations in voltage could cause the controller to go a little haywire. Secondly, maintain the proper salt level in the pool.

What percentage should my chlorinator be set to?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

How do I know if my salt cell needs replacing?

What Are Some Signs That Your Salt Cell May Need Replacing?Looking worse for wear, it’s lost a few plates and the acid baths just aren’t working.Your pool is starting to turn green or cloudy, even though your chlorinator is turned up to 100%.More items…

How long should I run my salt water chlorinator?

12 hoursYour pool system including chlorine generator should be operated often enough to completely turn your pool water over at least every 12 hours or twice a day.

At what temperature does a Salt Cell stop working?

60 degreesThe salt cell generators are made to work when pool water temperatures are above 60 degrees. In pool water temperatures that are 60 degrees or below, the salt generators simply shut down and by design do not allow the salt cell to ionize (breakdown) the salt and convert it to chlorine.

How long should I run my pool filter each day?

To keep your pool clean, all the water must run through your pump’s filter system at least once a day. This is called turnover rate. It’s simple: in order to run your pump effectively for eight hours, your pump should be able to process all of your pool water during that time.

What percentage should my salt cell be set at?

50 percentWe suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

How often should you backwash a pool?

As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.

Is a salt chlorinator worth it?

Salt systems will save you a ton of money on chemicals in the long run. While it is true that you will save money by not having to buy nearly as much chlorine, those savings are negated by the initial costs of buying the system, and the cost of replacing the cell every 5-7 years.

How often should a salt cell be cleaned?

every 2-6 monthsCleaning your Salt Cell. The number one maintenance item for a salt water chlorinator is to clean the salt cell regularly, every 2-6 months, but only as needed. Mineral deposits bridge the space between the metal plates, and not just in hard water areas.

Why does my salt chlorinator says no flow?

Check for damage to the wire itself. If you know your pump is running and there is sufficient water flow moving through your salt system but the “No Flow” LED is still illuminated, look on top of the flow switch itself to make sure the arrows on the flow switch are pointing in the same direction as the water flow.

How long after adding salt to pool Can you swim?

20 minutesYou should always wait at least 20 minutes before swimming in a pool you have added salt to so that it has time to dissolve and circulate.

Can I leave my pool pump off for a week?

First things first, your pool needs ample filter run time in order to keep up. At E-Z Test Pools we always recommend running the pump and filter 12 hours per day, every day. … If you know that you will be away for more than a week, it is best to have someone shock the pool once a week as well.

How long should my salt cell last?

about five yearsThis is all possible thanks to your pool’s salt chlorine generator cell. With proper care, a cell will last about five years. Eventually, though, it will need to be replaced. The trick is, it’s not always easy to know when it’s time.

Why is my saltwater pool not making chlorine?

Salinity. Chlorine generators need salt to produce chlorine and can’t do so if the amount of salt in the water is too low. … Get a salt-testing kit from a pool supplier and check to make sure that the levels are within this range. If your salinity is below 2,500 ppm, the generator will not be able to produce chlorine.

Is it bad to run your pool pump 24 hours a day?

Ideally, you should run your pump for 24 hours a day, but we know that’s unrealistic (and pricey), so let’s look for an answer that keeps your pool clean and your wallet full. Generally running your pool pump for 12-hours a day is a good option. … For a residential pool the water should turn over at least once per day.

Is it better to run pool pump at night?

It’s always best to run the pool pump during the hottest times of the day. … If you run your pump during the night, then the sun has all day to attack the chlorine that’s standing still in your pool. That can cause algae fast! It’s a great idea to have the pump running when people are using the pool.

Does pool pump use a lot of electricity?

Outside of the air conditioner, the pool pump is the largest electricity consumer in the average pool-containing home. According to the study, at the national average of 11.8 cents per KWh, a pool pump alone can add as much as $300 a year to an electric bill.

How do I know if my salt chlorinator is working?

Check Power: The Salt Cell is powered by the control panel, and before it reaches the salt cell, the incoming 115/230 VAC is stepped down to about 7-9 VDC, by a transformer. A simple way to check that power is on is to feel the power cord for warmth.